-
1 канал для электропроводки
канал для электропроводки
—
[Я.Н.Лугинский, М.С.Фези-Жилинская, Ю.С.Кабиров. Англо-русский словарь по электротехнике и электроэнергетике, Москва, 1999 г.]Тематики
- электротехника, основные понятия
EN
Русско-английский словарь нормативно-технической терминологии > канал для электропроводки
-
2 канал для электропроводки
electric raceway, racewayРусско-английский политехнический словарь > канал для электропроводки
-
3 кабельный канал
- trench for cabling
- raceway
- electric raceway
- duct
- conduit
- cabling
- cable trench
- cable duct
- cable channel
кабельный канал
Кабельным каналом называется закрытое и заглубленное (частично или полностью) в грунт, пол, перекрытие и т. п. непроходное сооружение, предназначенное для размещения в нем кабелей, укладку, осмотр и ремонт которых возможно производить лишь при снятом перекрытии.
[ПУЭ. Раздел 2]
кабельный канал
Элемент системы электропроводки, расположенный над землей или полом или в земле или в полу, открытый, вентилируемый или замкнутый, размеры которого не позволяют вход людей, но обеспечивают доступ к трубам и (или) кабелям по всей длине в процессе монтажа и после него.
Примечание - Кабельный канал может составлять или не составлять часть конструкции здания
[ ГОСТ Р МЭК 60050-826-2009]
канал кабельный
Подземный непроходной канал, предназначенный для размещения электрических кабелей
[Терминологический словарь по строительству на 12 языках (ВНИИИС Госстроя СССР)]EN
cable channel
element of a wiring system above or in the ground or floor, open, ventilated or closed, and having dimensions which do not permit the entry of persons but allow access to the conduits and/or cables throughout their length during and after installation
NOTE – A cable channel may or may not form part of the building construction.
[IEV number 826-15-06]FR
caniveau, m
élément de canalisation situé au-dessus ou dans le sol ou le plancher, ouvert, ventilé ou fermé, ayant des dimensions ne permettant pas aux personnes d'y circuler, mais dans lequel les conduits ou câbles sont accessibles sur toute leur longueur, pendant et après installation
NOTE – Un caniveau peut ou non faire partie de la construction du bâtiment.
[IEV number 826-15-06]
Кабельные каналы:
а — лотковый типа ЛК; б — из сборных плит типа СК:1 — лоток; 2 — плита перекрытия; 3 — подготовка; 4 — плита стеновая; 5 — основание
Высота кабельных каналов в свету не ограничивается, но бывает не более 1200 мм. Ширина каналов определяется в зависимости от размеров применяемых кабельных конструкций из условия сохранения прохода не менее 300 мм при глубине канала до 600 мм, 450 мм — от более 600 до 900 мм, 600 мм при более 900 мм.
Полы в каналах выполняют с уклоном не менее 0,5% в сторону водосборников или ливневой канализации.
Для крепления кабельных конструкций в стенах каналов через каждые 0,8—1 м (по длине) устанавливают закладные детали. При заводском изготовлении стеновых панелей детали устанавливают на предприятии-изготовителе. Закладные детали в каналах глубиной до 600 мм располагают в один ряд, при большей глубине каналов — в два ряда.
В местах поворота и разветвления трассы устраивают уширительные камеры, размеры которых выбирают с учетом допускаемого радиуса изгиба прокладываемого кабеля.
[ http://forca.ru/knigi/oborudovanie/priemka-zdaniy-i-sooruzheniy-pod-montazh-elektrooborudovaniya-11.html]Недопустимые, нерекомендуемые
Примечание(1)- Мнение автора карточкиТематики
- кабели, провода...
- электропроводка, электромонтаж
- электроустановки
Обобщающие термины
EN
- cable channel
- cable duct
- cable trench
- cabling
- conduit
- duct
- electric raceway
- raceway
- trench for cabling
DE
FR
- caniveau du câble
- caniveau, m
- conduite du câble
Русско-английский словарь нормативно-технической терминологии > кабельный канал
-
4 кабельный канал
1) Aviation: raceway area2) Engineering: Ultimedia Television, cable channel, cable duct, cable trench, cableway, conduit, duct run, electric raceway, raceway3) Construction: cable conduit4) Railway term: culvert5) TV: cable pathway6) Electronics: duct -
5 канал для электропроводки
1) Engineering: electric raceway, electrical wiring conduit, raceway2) oil&gas: conduitУниверсальный русско-английский словарь > канал для электропроводки
-
6 кабельный канал
-
7 кабельный канал
cabling, ( для электропроводки) electric racewayРусско-английский словарь по строительству и новым строительным технологиям > кабельный канал
-
8 труба для электропроводки
труба
Компонентзащищеннойтрубной электропроводки, имеющий, как правило, круглое поперечное сечение, предназначенный для прокладки изолированных проводов и(или) кабелей в электрических или коммуникационных установках, допускающий их затяжку в него и(или) их замену.
ПримечаниеСоединения труб должны быть достаточно плотными, чтобы изолированные провода и (или) кабели могли быть только затянуты, но не введены сбоку в просвет между трубами.
Трубы должны располагаться достаточно близко друг от друга, так чтобы отсутствовала возможность затянуть изолированные провода и (или) кабели в просвет между ними.
[ ГОСТ Р МЭК 60050-826-2009]
трубопроводтруба
Закрытый элемент кабельной конструкцииКомпонент трубной электропроводки круглого или иного сечения для прокладки в электрических установках кабелей и/или изолированных проводови/или кабелей в электрических установках,позволяющий производить ихвыемкузатяжку и/или замену.
Примечание
Трубопроводы должны быть закрыты таким образом, чтобы имелась возможность вставлять в них изолированные провода и/или кабели.
Трубы должны располагаться достаточно близко друг от друга, так чтобы отсутствовала возможность затянуть изолированные провода и (или) кабели в просвет между ними.
[ ГОСТ Р МЭК 60204-1-2007]
Примечание. Синим цветом обозначен вариант, предлагаемый автором карточки.EN
conduit
a part of a closed wiring system of generally circular cross section for insulated conductors and/or cables in electrical or communication installations, allowing them to be drawn in and/or replaced
Source: 826-06-03 MOD
[IEV number 442-02-03]
conduit
part of a closed wiring system of circular or non-circular cross-section for insulated conductors and/or cables in electrical installations, allowing them to be drawn in and/or replaced
NOTE Conduits should be sufficiently close-jointed so that the insulated conductors and/or cables can only be drawn in and not inserted laterally.
[IEV 826-06-03]
[IEC 60204-1-2006]
raceway
A tube that encloses and protects electric wires.
[ http://www.answers.com/topic/raceway]FR
conduit
élément d'un système de canalisation fermé de section droite généralement circulaire, destiné à la mise en place par tirage ou au remplacement des conducteurs ou des câbles isolés dans les installations électriques ou de télécommunication
Source: 826-06-03 MOD
[IEV number 442-02-03]См. также пластмассовые трубы для электропроводок
См. также стальные трубы для электропроводок
4.1. Для прокладки проводов и кабелей необходимо применять специальные трубы для электропроводок: гладкие из непластифицированного ПВХ по ТУ 6-19-215-86, прил. 2; гладкие из вторичного ПЭ по ТУ 63.178-103-85, прил. 3; гладкие из наполненного ПЭ по ТУ 6-19-051-575-85, прил. 4; гофрированные из НПВХ по ТУ 6-19-051-419-84, прил. 5; гофрированные из ПЭ по ТУ 6-19-051-518-87, прил.6; гофрированные из вторичного ПЭ по ТУ 63.178-117-87, прил.7. При отсутствии указанных труб применяют технологические трубы: гладкие напорные из НПВХ по ТУ 6-19-231-87, прил.8; гладкие напорные из ПЭ низкого и высокого давления по ГОСТ 18599-83, прил. 9; гладкие из ПП по ТУ 38-102-100-76, прил. 10; трубы из вторичного ПЭ по ТУ 6-19-133-79, прил. П.
...
4.3. Применяют также трубы стальные электросварные по ГОСТ 10704-76 сортамент, прил. 12, легкие и обыкновенные водогазопроводные по ГОСТ 3262-75*, прил.13.[Министерство архитектуры, строительства и жилищно-коммунального хозяйства. Концерн «ЭЛЕКТРОМОНТАЖ». Инструкция по монтажу электропроводок в трубах]
Недопустимые, нерекомендуемые
Примечание(1)- Мнение автора карточкиТематики
- электропроводка, электромонтаж
Синонимы
EN
DE
FR
Русско-английский словарь нормативно-технической терминологии > труба для электропроводки
-
9 длительный допустимый ток
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Русско-английский словарь нормативно-технической терминологии > длительный допустимый ток
-
10 металлические изделия для электропроводки, прокладываемой по поверхности стен и потолков
металлические изделия для электропроводки, прокладываемой по поверхности стен и потолков
-
[Интент]EN
surface metal raceway
A raceway which consists of a surface-mounted assembly of metal backing (providing mechanical support) and capping (providing a protective covering); used for electric wiring for branch circuits or feeder conductors.
detail of surface metal raceway
surface metal raceway: 90° bend
[ http://www.answers.com/topic/surface-metal-raceway-1]Тематики
- электропроводка, электромонтаж
EN
Русско-английский словарь нормативно-технической терминологии > металлические изделия для электропроводки, прокладываемой по поверхности стен и потолков
-
11 изделия для электропроводки, размещаемые в полу
изделия для электропроводки, размещаемые в полу (ниже уровня чистого пола)
-
[Интент]EN
underfloor raceway
A raceway for electric wires which runs beneath the floor.
[http://www.answers.com/topic/underfloor-raceway]Тематики
- электропроводка, электромонтаж
EN
Русско-английский словарь нормативно-технической терминологии > изделия для электропроводки, размещаемые в полу
-
12 система кабельных коробов
система кабельных коробов
Система замкнутых оболочек, состоящих из основания (корпуса) и съемной крышки, предназначенная дляполного заключения в себяпрокладки внутри неё изолированных проводов, кабелей, шнуров и (или) для размещения другого электрического оборудования, включая оборудование информационных технологий.
[ ГОСТ Р МЭК 60050-826-2009]
система кабельных коробов
Система замкнутых оболочек, состоящих из корпуса со съемной или открывающейся крышкой, предназначенная для прокладки внутри нее изолированных проводов, кабелей и шнуров и/или для размещения другого электрооборудования.
[ ГОСТ Р МЭК 61084-1 2007]
кабельнесущая система
Система закрытых оболочек, допускающая размещение изолированных проводов на базе подвижных поверхностей и предназначенная для полной защиты изолированных проводов, кабелей, шнуров, а также для размещения другого электрооборудования.
система кабельных коробов
Система закрываемых полых конструкций, состоящая из основания (корпуса) и съемной крышки, предназначенная для прокладки внутри них и защиты от механических повреждений кабелей, шнуров, изолированных проводов и (или) для размещения другого электрического оборудования, включая оборудование информационных технологий.
[ ГОСТ Р МЭК 60204-1-2007]
Примечание. Синим цветом обозначен вариант, предлагаемый автором карточки.EN
cable trunking system
a system of closed enclosures comprising a base with a removable cover, intended for the complete surrounding of insulated conductors, cables, cords and/or for the accommodation of other electrical accessories
Source: 826-06-04 MOD
[IEV number 442-02-34]
cable trunking system
system of closed enclosures comprising a base with a removable cover, intended for the complete surrounding of insulated conductors, cables, cords and/or for the accommodation of other electric equipment including information technology equipment
Source: 442-02-34 MOD
[IEV number 826-15-04]
[IEC 60204-1-2006]FR
système de goulottes
ensemble d'enveloppes fermées munies d'un fond avec un couvercle amovible et destiné à la protection complète de conducteurs isolés et de câbles, ou au logement d'autre petit appareillage électrique
Source: 826-06-04 MOD
[IEV number 442-02-34]
système de goulottes, m
ensemble d'enveloppes fermées, munies d'un fond avec un couvercle amovible et destiné à la protection complète des conducteurs isolés et des câbles et/ou au logement d'autres matériels électriques y compris des matériels de traitement de l'information
Source: 442-02-34 MOD
[IEV number 826-15-04]Обратите внимание!
Различают два вида систем кабельных коробов:
1) (просто) система кабельных коробов (cable trunking system) - система любого сечения, но обязательно с крышкой;
2) система специальных кабельных коробов (cable ducting system) - система некруглого сечения и без крышек.
Примечание. В ПУЭ короб без крышки называется глухой короб (см. кабельный короб)
[Автор карточки]
Параллельные тексты EN-RU
Raceways shall be one- or two-piece design with base and snap-on cover, or three-piece design with base and two snap-on covers which snap side by side on a common base.
[Legrand/Wiremold. SECTION 16130 RACEWAY AND BOXES]В состав поставки входят специальные (глухие) кабельные короба, а также кабельные короба, состоящие из основания и защелкивающейся крышки, или из основания и двух защелкивающихся крышек.
[Перевод Интент]
1 - Система кабельных коробов
Система кабельных коробов
Система кабельных коробов
Недопустимые, нерекомендуемые
Примечание(1) - мнение автора карточкиТематики
- изделие электромонтажное
- электропроводка, электромонтаж
EN
DE
FR
Русско-английский словарь нормативно-технической терминологии > система кабельных коробов
-
13 протяжная коробка
протяжная коробка
-EN
pull box
In electric wiring, a box (with a removable cover) that is inserted in one or more runs of raceway to facilitate the pulling of conductors through the raceway.
[ http://www.answers.com/topic/pull-box-1]
Коробка протяжная КП-1 предназначена для соединения и ответвления проводов, кабелей при выполнении электропроводок и кабельных линий напряжением до 1000 В, в том числе при скрытой электропроводке.
8.21. Расстояние между протяжными коробками (ящиками) для стальных и пластмассовых труб не должно превышать следующих значений: на прямых участках - 75 м; при одном изгибе трубы - 50 м; при двух изгибах - 40 м; при трех изгибах - 20 м.
[Министерство архитектуры, строительства и жилищно-коммунального хозяйства. Концерн «ЭЛЕКТРОМОНТАЖ». Инструкция по монтажу электропроводок в трубах]
Тематики
- электропроводка, электромонтаж
EN
Русско-английский словарь нормативно-технической терминологии > протяжная коробка
-
14 канал в перекрытии для электропроводки и телефонных сетей
Construction: raceway for electric conduit and telephone linesУниверсальный русско-английский словарь > канал в перекрытии для электропроводки и телефонных сетей
-
15 трубка (трубопровод)
pipe
- бурдона — bourdon tube, pressure spring
пружинящий, трубчатый элемент манометра, воспринимающий подводимое давление и преобразующий его в механическое перемещение стрелки прибора (рис.81). — а brass (cooper) element of а pressure gage which translates the internal pressure into mechanical movement to actuate indicator needle. lnternal pressures cause the loose end of the element to spread out or uncoil.
- вентури — venturi tube
трубка с суживающимися внутри каналом и отверстием в месте сужения, в котором происходит увеличение скорости и уменьшение давления, протекающего по трубке потока. — a short tube of smaller diameter in the middle than at the ends. when air flows through such a tube, the pressure dacreases as the diameter becomes smaller, the amount of the decrease being proportional to the speed of flow.
-, гофрированная (соединительная) — bellows
-, дозирующая (в системе кондиционирования воздуха) — venturi tube
-, дренажная (бака) — vent pipe
-, дренажная (слива утечек) — drainage pipe
-, заборная (бака) — outlet pipe
-, заливная (амортстойки) — oil level tube
- замера давления (датчика манометра) — (pressure transmitter) inlet pipe
- замера давления (в коллекторе) — (manifold) pressure measurement pipe
-, измерительная (уровня электролита) — (electrolyte level) measuring tube
- импульсная (для подвода давления к сигнализатору давления или манометру) — (pressure switch or transmitter) inlet pipe
-, капиллярная (рис.75) — capillary tube
-, критическая (системы кондиционирования воздуха) — venturi tube
критическая или мерная т. может использоваться в качестве расходомера воздуха урвк. — may be used as airflow metering unit in air conditioning system.
-, критическая ограничения потока (воздуха) — (air) flow limiting venturi
-, манометрическая (бурдона) — pressure spring
-, микротелефонная (у рабочего места бортпроводника. дпя внутрисамолетной связи) — handset the handset is switched to interphone system, when it is placed on its hanger.
- пито (приемник полного давления, ппд) (рис.83) — phot tube
- препарирования (для замера давления) — pressure measurement pipe
-, резиновая — rubber pipe /tube/
-, сильфонная — bellows
- слива отстоя (из топливных баков) — sediment drain pipe
-, стеклянная — glass tube
- суфлера (двиг.) — breather pipe
-, суфлерная (сообщ. с атмосферой) — vent pipe
- указателя скольжения — slip indicator curved glass tube
- холодной пристрелки или отработки (тхп) — boresight tool /tube/
- холодной пристрелки антенны — antenna bore sighting) tool /tube/
-, экранирующая (для электрической проводки) — conduit а tubular raceway for holding and shielding wires or cables.
-, электронно-лучевая — cathode ray tube (crt)
- электропроводки — electric wiring conduitРусско-английский сборник авиационно-технических терминов > трубка (трубопровод)
-
16 тонкостенная металлическая труба для электропроводки
тонкостенная металлическая труба для электропроводки
-EN
electrical metallic tubing
A thin-walled metal raceway having a circular cross section; used to pull in or withdraw electric cables or wires after the tubing is installed in place; uses connectors and couplings other than the threaded type.
[ http://www.answers.com/topic/electrical-metallic-tubing-1]
intermediate metal conduit
IMC
-Intermediate metal conduit, or IMC for short, is a rigid steel electrical conduit that is lighter in weight than another rigid conduit. It was designed specifically to protect insulated electrical conductors and cables. It does the work of a similar conduit, galvanized rigid conduit (GRC), but with much less weight and thickness size. By utilizing IMC in areas allowed, you can all but eliminate the need for a heavier wall conduit.
IMC has other advantages over GRC. It has a larger interior diameter than Galvanized Rigid Conduit and the smoother interior of the pipe allows for easier wire pulling through the conduit.
IMC was originally introduced by Allied Tube & Conduit Corporation. It is manufactured in accordance with Underwriters’ Laboratories safety standard 1242 and ANSI C80.6. Believe it or not, Allied claims that IMC is actually more rigid than GRC in applications such as service masts and other installations. It has been installed in industrial and commercial buildings. In fact, the National Electrical Code has a specific article about IMC, article 342.
IMC conduit is coated in a hot galvanized coating on the exterior and a special corrosive-resistant coating on the inside to extend the conduit’s lifespan for reliability. Common conduit sizes range from ½” to 4”.
[ http://electrical.about.com/od/metalpvcconduit/a/IMCconduit.htm]Тематики
- электропроводка, электромонтаж
EN
Русско-английский словарь нормативно-технической терминологии > тонкостенная металлическая труба для электропроводки
См. также в других словарях:
raceway — ☆ raceway [rās′wā΄ ] n. 1. a narrow channel for water 2. any conduit for carrying and protecting electric wires 3. RACE1 (sense 7) 4. a racetrack for harness racing 5. a racetrack for drag racing, stock cars, etc … English World dictionary
raceway — noun chiefly N. Amer. 1》 a water channel, especially an artificial one for rearing fish. 2》 a groove or race for bearings. 3》 a pipe or tubing enclosing electric wires. 4》 a racecourse or racetrack … English new terms dictionary
Pole Position Raceway — is a chain of indoor kart tracks in the United States. The company was founded by Jason Williams and Ken Faught. The company opened its first track in Corona, California in September 2005 [Reference for the time the company opened… … Wikipedia
Orange County International Raceway — was a combined ¼ mile US dragstrip and 2 mile road course located in Irvine, California adjacent to the Interstate 5 (I 5) Santa Ana Freeway. Under a lease agreement with the Irvine Company, OCIR as it was known in racing circles was in operation … Wikipedia
Graybar Electric Company — Infobox Company name = Graybar Electric Company, Inc. type = Private/Employee Owned company slogan = Works to Your Advantage foundation = 1869 founder = Elisha Gray and Enos Barton location city = St. Louis, Missouri location country = U.S.… … Wikipedia
кабельный канал — Кабельным каналом называется закрытое и заглубленное (частично или полностью) в грунт, пол, перекрытие и т. п. непроходное сооружение, предназначенное для размещения в нем кабелей, укладку, осмотр и ремонт которых возможно производить лишь при… … Справочник технического переводчика
канал для электропроводки — — [Я.Н.Лугинский, М.С.Фези Жилинская, Ю.С.Кабиров. Англо русский словарь по электротехнике и электроэнергетике, Москва, 1999 г.] Тематики электротехника, основные понятия EN racewayelectric raceway … Справочник технического переводчика
Hutt Park Railway Station, Gracefield — Infobox Station name=Hutt Park type=New Zealand Government Railways Department suburban rail image size= image caption=Hutt Park railway station, looking south. The platform now borders private land and the Hutt Valley Golf Course on the… … Wikipedia
Drag racing — Drag racer and Drag race redirect here. For other uses, see Drag racing (disambiguation). The Christmas tree counting down at SIR. Note the blinder, to prevent the driver from being distracted by the light for the other lane. Drag racing is a… … Wikipedia
Dodge City, Kansas — Dodge City redirects here. For others, see Dodge (disambiguation). Dodge City, Kansas City The El Capitan cattle drive monument, 2 … Wikipedia
Electrical conduit — risers, seen inside fire resistance rated shaft, as seen entering bottom of a firestop. The firestop is made of firestop mortar on top, rockwool on the bottom. Raceways are used to protect cables from damage … Wikipedia